All guides
P0359
Difficulty: ModerateTime: 2-4 hoursUpdated: March 10, 2025

2017 NISSAN ALTIMA P0359: Ignition Coil I Primary/Secondary Circuit Malfunction

The P0359 diagnostic trouble code affects 2017 NISSAN ALTIMA vehicles and indicates a specific malfunction in the ignition coil i primary/secondary circuit malfunction system. This comprehensive guide provides complete diagnostic procedures, repair strategies, and expert-level troubleshooting specifically tailored for your vehicle.

Understanding the P0359 in Your 2017 ALTIMA

When your 2017 NISSAN ALTIMA triggers the P0359 diagnostic trouble code, it indicates a specific malfunction within the vehicle's engine management system. This code is part of the onboard diagnostic system that monitors the performance of critical engine components in real-time.

Your ALTIMA utilizes an advanced engine control module (ECM/PCM) that integrates multiple sensors and control systems to optimize power delivery, fuel efficiency, and emissions performance. When the P0359 code sets, it means the control module has detected a signal that falls outside acceptable parameters established during vehicle engineering.

Common Symptoms of P0359

2017 NISSAN ALTIMA vehicles experiencing P0359 may exhibit the following symptoms:

  • Misfire symptoms and rough engine operation
  • Check engine light on your 2017 NISSAN ALTIMA
  • Engine may run on fewer cylinders than normal
  • Hard starting or no start condition

If you notice any of these symptoms in your ALTIMA, it is recommended to have the vehicle diagnosed by a qualified technician to prevent potential engine damage or reduced performance.

Common Causes of P0359

Several factors can trigger the P0359 diagnostic trouble code in your 2017 ALTIMA:

  • Failed ignition coil(s) not producing adequate spark
  • Ignition coil driver circuit malfunction in PCM
  • Damaged spark plug wires or boots
  • Ground connection issues affecting coil operation

Understanding these potential causes helps narrow down the diagnostic process and ensures accurate repair identification.

Diagnostic Procedures for P0359

Professional diagnosis of the P0359 code in your 2017 NISSAN ALTIMA requires systematic troubleshooting using proper diagnostic equipment.

Initial Scan and Data Retrieval

Begin by connecting a professional-grade OBD-II scan tool to the vehicle's diagnostic connector. Record all stored codes, including pending and permanent codes, along with freeze frame data. The freeze frame information captures the exact operating conditions present when the code first set, providing valuable diagnostic context.

For NISSAN ALTIMA vehicles, accessing manufacturer-specific data streams provides deeper insight into sensor performance and system operation. Pay particular attention to live data parameters related to the affected circuit during various engine operating conditions.

Visual Inspection

Thoroughly inspect all accessible wiring harnesses and connectors in the affected circuit. Look for signs of chafing, insulation damage, or connector deterioration. On the ALTIMA, pay special attention to connections near the engine and transmission, where heat and vibration can accelerate connector failure.

Inspect the physical components for obvious signs of damage or wear. Check for leaks, cracks, or loose mounting hardware. Verify component mounting conditions and proper installation.

Electrical Testing

Using a digital multimeter and oscilloscope, perform electrical tests on the suspect circuit. Verify proper voltage supply, ground circuit integrity, and signal output characteristics. Compare your findings against manufacturer specifications for the 2017 ALTIMA.

For complex circuit diagnosis, use appropriate diagnostic tools to verify bus integrity, termination resistance, and communication protocols between control modules.

Repair Strategies and Solutions

Once you've identified the root cause of the P0359 code in your 2017 NISSAN ALTIMA, implement the appropriate repair using quality replacement parts and factory-approved procedures.

Component Replacement

If diagnosis reveals a failed component in the circuit, replace the component with an OEM or quality aftermarket equivalent. For optimal performance and longevity, NISSAN genuine parts are recommended, particularly for critical sensors affecting emissions and drivability.

After component replacement, clear the diagnostic trouble codes and perform a road test to verify the repair. Many sensors require basic calibration procedures using appropriate diagnostic equipment. On ALTIMA vehicles with advanced features, additional adaptation procedures may be necessary.

Wiring Repair

Damaged wiring should be repaired using appropriate methods including solder joints, heat-shrink insulation, and weatherproof connectors. Avoid using tape or wire nuts for engine compartment repairs, as these methods are unreliable in the demanding thermal and vibrational environment.

When repairing wiring on your ALTIMA, ensure proper wire routing away from heat sources and moving components. Secure harnesses using factory-style clips and brackets to prevent future damage from chafing or vibration.

Module Considerations

If the PCM or another control module is determined to be faulty, replacement requires programming using dealer-level diagnostic equipment. The P0359 code may indicate internal module failure requiring specialized services available at authorized dealerships or qualified independent repair facilities.

NISSAN-Specific Considerations for ALTIMA Vehicles

The 2017 ALTIMA features unique engineering that requires specialized knowledge during diagnosis and repair. Understanding these manufacturer-specific characteristics improves diagnostic accuracy and repair success.

Regular maintenance plays a crucial role in preventing P0359 codes and maintaining optimal engine performance. Follow the manufacturer's recommended maintenance schedule, paying particular attention to items affecting ignition, fuel delivery, and engine timing systems.

Use only recommended fluids and replacement parts to ensure compatibility with your vehicle's sophisticated engine management system. Quality maintenance helps prevent premature component failures that can trigger diagnostic trouble codes.

Prevention and Maintenance Tips

Preventing future occurrences of the P0359 diagnostic trouble code in your 2017 NISSAN ALTIMA requires consistent maintenance and attention to warning signs.

Follow the manufacturer's recommended maintenance schedule for your ALTIMA, paying particular attention to items affecting the ignition and fuel systems. Regular inspection of ignition components, fuel system maintenance, and timely replacement of worn parts all contribute to preventing misfire codes.

Monitor your vehicle's performance between service appointments. Changes in drivability, unusual noises, or illuminated warning lights should prompt immediate attention before they develop into more serious problems.

Cost Considerations

The cost to diagnose and repair the P0359 code in your 2017 NISSAN ALTIMA varies significantly based on the root cause and your chosen repair facility.

Simple sensor replacements typically cost between $100 and $400 for parts and labor. More complex repairs involving wiring harness repair or component replacement can range from $300 to $1,000 or more. If the code stems from PCM or module failure, expect costs of $800 to $2,500 for diagnosis, repair, and programming.

Dealerships generally charge higher labor rates but offer factory-trained technicians and genuine OEM parts. Independent shops with proper diagnostic equipment can provide quality repairs at more competitive prices. Always obtain detailed estimates before authorizing repairs.

Conclusion

The P0359 diagnostic trouble code in your 2017 NISSAN ALTIMA requires systematic diagnosis to identify the underlying cause and implement proper repairs. Using the procedures outlined in this guide, combined with quality replacement parts and proper calibration, you can resolve this issue and restore your vehicle to optimal performance.

For complex engine management issues or if you lack the specialized diagnostic equipment required for ALTIMA service, consult a qualified technician. The advanced technology in modern vehicles benefits from professional service by technicians familiar with manufacturer-specific diagnostic procedures and repair techniques.